# SPDX-FileCopyrightText: 2017 Scott Shawcroft for Adafruit Industries
#
# SPDX-License-Identifier: MIT
"""
`adafruit_motor.servo`
====================================================
Servos are motor based actuators that incorporate a feedback loop into the design. These feedback
loops enable pulse width modulated control to determine position or rotational speed.
* Author(s): Scott Shawcroft
"""
__version__ = "0.0.0-auto.0"
__repo__ = "https://github.com/adafruit/Adafruit_CircuitPython_Motor.git"
# We disable the too few public methods check because this is a private base class for the two types
# of servos.
class _BaseServo: # pylint: disable-msg=too-few-public-methods
"""Shared base class that handles pulse output based on a value between 0 and 1.0
:param ~pwmio.PWMOut pwm_out: PWM output object.
:param int min_pulse: The minimum pulse length of the servo in microseconds.
:param int max_pulse: The maximum pulse length of the servo in microseconds."""
def __init__(self, pwm_out, *, min_pulse=750, max_pulse=2250):
self._pwm_out = pwm_out
self.set_pulse_width_range(min_pulse, max_pulse)
def set_pulse_width_range(self, min_pulse=750, max_pulse=2250):
"""Change min and max pulse widths."""
self._min_duty = int((min_pulse * self._pwm_out.frequency) / 1000000 * 0xFFFF)
max_duty = (max_pulse * self._pwm_out.frequency) / 1000000 * 0xFFFF
self._duty_range = int(max_duty - self._min_duty)
@property
def fraction(self):
"""Pulse width expressed as fraction between 0.0 (`min_pulse`) and 1.0 (`max_pulse`).
For conventional servos, corresponds to the servo position as a fraction
of the actuation range. Is None when servo is diabled (pulsewidth of 0ms).
"""
if self._pwm_out.duty_cycle == 0: # Special case for disabled servos
return None
return (self._pwm_out.duty_cycle - self._min_duty) / self._duty_range
@fraction.setter
def fraction(self, value):
if value is None:
self._pwm_out.duty_cycle = 0 # disable the motor
return
if not 0.0 <= value <= 1.0:
raise ValueError("Must be 0.0 to 1.0")
duty_cycle = self._min_duty + int(value * self._duty_range)
self._pwm_out.duty_cycle = duty_cycle
[docs]class Servo(_BaseServo):
"""Control the position of a servo.
:param ~pwmio.PWMOut pwm_out: PWM output object.
:param int actuation_range: The physical range of motion of the servo in degrees, \
for the given ``min_pulse`` and ``max_pulse`` values.
:param int min_pulse: The minimum pulse width of the servo in microseconds.
:param int max_pulse: The maximum pulse width of the servo in microseconds.
``actuation_range`` is an exposed property and can be changed at any time:
.. code-block:: python
servo = Servo(pwm)
servo.actuation_range = 135
The specified pulse width range of a servo has historically been 1000-2000us,
for a 90 degree range of motion. But nearly all modern servos have a 170-180
degree range, and the pulse widths can go well out of the range to achieve this
extended motion. The default values here of ``750`` and ``2250`` typically give
135 degrees of motion. You can set ``actuation_range`` to correspond to the
actual range of motion you observe with your given ``min_pulse`` and ``max_pulse``
values.
.. warning:: You can extend the pulse width above and below these limits to
get a wider range of movement. But if you go too low or too high,
the servo mechanism may hit the end stops, buzz, and draw extra current as it stalls.
Test carefully to find the safe minimum and maximum.
"""
def __init__(self, pwm_out, *, actuation_range=180, min_pulse=750, max_pulse=2250):
super().__init__(pwm_out, min_pulse=min_pulse, max_pulse=max_pulse)
self.actuation_range = actuation_range
"""The physical range of motion of the servo in degrees."""
self._pwm = pwm_out
@property
def angle(self):
"""The servo angle in degrees. Must be in the range ``0`` to ``actuation_range``.
Is None when servo is disabled."""
if self.fraction is None: # special case for disabled servos
return None
return self.actuation_range * self.fraction
@angle.setter
def angle(self, new_angle):
if new_angle is None: # disable the servo by sending 0 signal
self.fraction = None
return
if new_angle < 0 or new_angle > self.actuation_range:
raise ValueError("Angle out of range")
self.fraction = new_angle / self.actuation_range
[docs]class ContinuousServo(_BaseServo):
"""Control a continuous rotation servo.
:param int min_pulse: The minimum pulse width of the servo in microseconds.
:param int max_pulse: The maximum pulse width of the servo in microseconds."""
@property
def throttle(self):
"""How much power is being delivered to the motor. Values range from ``-1.0`` (full
throttle reverse) to ``1.0`` (full throttle forwards.) ``0`` will stop the motor from
spinning."""
return self.fraction * 2 - 1
@throttle.setter
def throttle(self, value):
if value > 1.0 or value < -1.0:
raise ValueError("Throttle must be between -1.0 and 1.0")
if value is None:
raise ValueError("Continuous servos cannot spin freely")
self.fraction = (value + 1) / 2
def __enter__(self):
return self
def __exit__(self, exception_type, exception_value, traceback):
self.throttle = 0